Whirlpool JUD248CCCR Specifikace

TECHNICAL EDUCATIONJOB AID 4317434R-1072008 DOUBLE DRAWERREFRIGERATOR / FREEZERUNDER COUNTERPRODUCTSKDDC24RVSKDDO24RVXKDDC24CVSKDDO24CVXKDDC24FVSKDDO2

2-2LOCATION REQUIREMENTSNOTES:For the refrigerator drawers to be ush • with the front of the base cabinets remove any baseboards or moldings from

2-3WATER SUPPLY REQUIREMENTSGather the required tools and parts before starting installation.Read and follow the instructions provided with any

2-4PRODUCT DIMENSIONSSTYLES 1 AND 2: ARCHITECT® SERIES AND OVERLAYHeight dimensions are shown with the • leveling legs extended to 1/4" (

3-1THEORY OF OPERATIONOPERATING SYSTEMS1) General Cooling Operation of the RR (All Refrigerator) and FF (All Freezer) There is an upper chamber

3-2As the usual start up, the main PCB turns on the condenser fan and after 10 seconds the compressor will start. The compressor will continue to run

3-3REFRIGERATOR/FREEZER COMBO COOLING OPERATION1. Power On: Compressor, condenser fan and the freezer evaporator fan turns on. The refrigerator evap

3-4REFRIGERATOR/FREEZER COMBO DEFROST CYCLEThe defrost cycle starts after ten hours of compressor run time.The condenser fan runs for two minutes afte

4-1COMPONENT ACCESS To remove the top drawer: 1. Open the drawer. 2. Locate the wiring harness on the left side  ofthedrawer,seegure1. 3.

4-2DRAWER INSTALLATIONElectrical Shock HazardDisconnect power before servicing.Replace all parts and panels before operating.Failure to do so can r

4-3REMOVING DRAWER FRONT, GASKET AND DRAWER HANDLE1.Removetwoscrewsonbothsidesofthe drawersecuringthedrawercoverand drawer. 2. Sep

- ii -WHIRLPOOL CORPORATION assumes no responsibility for any repairs made on our products by anyone other than In-Home Service Professionals.FORWARDT

4-4REMOVING THE USER INTERFACE BOARDFigure1Figure2Figure4Figure5Figure31.Removethefourscrewssecuringtheuser interfacehousingtothed

4-5Electrical Shock HazardDisconnect power before servicing.Replace all parts and panels before operating.Failure to do so can result in death or e

4-6Evaporator FanEvaporator FanRefrigerator ThermistorFreezer ThermistorFreezer LightsWire Harness For User InterfaceModularIceMakerDoor SwitchDoor

4-7Electrical Shock HazardDisconnect power before servicing.Replace all parts and panels before operating.Failure to do so can result in death or e

4-8REMOVING THE SEPARATOR Electrical Shock HazardDisconnect power before servicing.Replace all parts and panels before operating.Failure to do so c

4-9REMOVING THE SEPARATOR (continued)5. Drop the evaporator cover down to access the wiring harness connector located in the top right hand corne

4-10REMOVING THE SEPARATOR (continued)The evaporator fan motors and Thermistors areservicedfromthebacksideoftheevapo-ratorcover,seegure11

4-11EVAPORATOR COMPONENTSElectrical Shock HazardDisconnect power before servicing.Replace all parts and panels before operating.Failure to do so ca

4-12MACHINE COMPARTMENT COMPONENTSElectrical Shock HazardDisconnect power before servicing.Replace all parts and panels before operating.Failure to

4-13Overload Removed Overload RunCapacitorFoam Pad12mfdRunCapacitorRelayMACHINE COMPARTMENT (continued)

- iii -TABLE OF CONTENTSPage(s)GENERAL ...

4-14REMOVING THE WATER VALVEFigure1Figure3Figure4Figure21.Removeinsulationstriplocatednexttoleft sideofthecabinet,seegure1.3.R

4-15CONDENSER AND PC BOARDA metal plate covers the condenser, seegure1. Condenser cover removed, DoubleDrawerrefrigeratormodel,seegure2.

4-16NOTES

5-1DIAGNOSTICS AND TROUBLESHOOTINGMAIN PCB CONNECTOR FUNCTIONJ1 Defrost Heater, Thermal FuseJ2 Ice MakerJ4 Power Supply, CompressorJ5 Display,

5-2MAIN PCB CONNECTOR FUNCTION (continued)J4 Power Supply, Compressor #1 pin connects to Green wire and Frame. #2 pin connects to Black w

5-3MAIN PCB CONNECTOR FUNCTION (continued)DISPLAY PCB CONNECTOR FUNCTIONJ7 Condenser Fan Motor #2 will be 0V when Condesor Fan Motor is working.

5-4BUILT-IN BOARD DIAGNOSTICSTest User Interface DisplayPress and hold "deg. C" and "-" simultane-ously for 5 seconds to start the

6-1WIRING DIAGRAMS

6-2WIRING DIAGRAMS (continued)

PRODUCT SPECIFICATIONS AND WARRANTY INFORMATION SOURCESIN THE UNITED STATES:FOR PRODUCT SPECIFICATIONS AND WARRANTY INFORMATION CALL:FOR TECHNICAL ASS

- iv -NOTES

1-1GENERALREFRIGERATOR / FREEZER SAFETYYour safety and the safety of others are very important.We have provided many important safety messages i

1-2DESIGN SPECIFICATIONS24" Drawer ModelsDouble Refrigerator DrawersTwo refrigerator drawers provide additional storage options in the kitchen or

1-3DESIGN SPECIFICATIONS (continued)24" Drawer ModelsDouble Refrigerator DrawersTwo refrigerator drawers provide additional storage options in th

1-4MODEL AND SERIAL NUMBER LABEL LOCATIONThe Model/Serial Number label location is shown below.After pulling the upper drawer out, the Model/Serial Nu

2-1Before you move the refrigerator into its nal location, it is important to make sure you have the proper electrical connection: • A 115 Volt, 60