Whirlpool AKM 231/IX Návod k použití stáhnout pdf (Strana 3)

INSTALLATION

TECHNICAL INFORMATION FOR THE INSTALLER

• This product can be embedded in a worktop 20 to 40 mm thick.

• If there is no oven beneath the hob, insert a separator panel that has a surface at least equal to the opening

in the work surface. This panel must be positioned at a maximum distance of 150 mm below the upper

surface of the work surface but, in no case less than 20 mm from the bottom of the hob. In the case that you

intend to install an oven beneath the hob, make sure that it is manufactured by Whirlpool and equipped

with a cooling system. The manufacturer declines all liability if another brand oven is installed beneath the

hob.

• Before installation, make sure that:

- the local gas delivery conditions (nature and pressure) are compatible with the settings of the hob (see the

rating plate and injector table).

- The outer surfaces of the furniture or appliances adjacent to the hob are heat resistant according to local regulations.

- Combustion products are discharged outdoors through specific hoods or wall and/or window mounted electrical fans.

GAS CONNECTION

• The gas supply system must comply with local regulations.

• You can find specific local regulations for some countries in the paragraph “Reference to Local Regulations”. If no

information concerning your Country is given, please ask details to your Installer.

• The connection of the hob to the gas pipe network or gas cylinder must be made by means of a rigid copper or steel

pipe with fittings complying with local regulations, or by means of a continuous-surface stainless steel hose complying

with local regulations. The maximum length of the hose is 2 linear metres.

• Before connecting the tube to the elbow fitting (A), interpose the

washer (B) supplied, in compliance with EN 549.

For Belgium - replace the elbow connection with the one supplied in the kit.

Attention: if a stainless steel hose is used, it must be installed so as not to touch any mobile part of the furniture.

It must pass through an area where there are no obstructions and where it is possible to inspect it on all its length.

• After connection to the gas supply, check for leaks with soapy water.

ELECTRICAL CONNECTION

• The electrical connections must comply with local regulations.

• The data relevant to the voltage and power absorption are indicated on the rating plate.

• The earthing of this appliance is compulsory by law.

• The manufacturer cannot be held responsible for any injury to persons or animals or damage to property

arising from failure to comply with these requirements.

• When the hob is installed, provide a multi-pole circuit breaker with a contact separation of at least 3 mm.

• If necessary, the electrical power cable must be replaced exclusively with a power cable having identical

characteristics to the original supplied by the manufacturer (type H05V2V2-F T90°C or H05RR-F).

This operation must be performed by a qualified electrician.

Earth

(yellow/green)

HOB WITH UNIVERSAL JOINTS

Fix the hob to the countertop and then install the oven [check

also oven installation instructions].

Universal (cardan) joints are sized to ensure proper operation

for hob installed in the top that is 50mm thick.

1. Connect tongues (A) to ending (B) as shown in the figure.

2. If your hob is equipped with an electric hotplate, connect 3-

plug assembly (R) to the first 3 bores of the 5 pole terminal

board on block (A) as shown in figure.

3. Position the oven and fix it with screws supplied.

4. Fit the knobs by pressing them into their seats on the

control panel.

NOTE: In case of instalation with worktop thickness of

25mm authorized installer should cut plastic shaft of the joint

like shown in the LEAFLET. After assembly authorized

installer should check hob operation by turning and pressing

the knobs to check the burner ignition 5-10 seconds after

ignition when installer stops pushing the knob burner should

remain lit.

IMPORTANT: when the burners are not lit, gas should flow

only when you push and turn the knob.

THE GAS MUST NOT FLOW IF THE KNOB IS NOT

PRESSED.

ASSEMBLY

After having cleaned the perimeter surface, apply the supplied

gasket to the hob as shown in the figure.

Position the hob in the worktop opening made respecting

the dimensions indicated in the Instruction.

Note: the power supply cable must be long enough

to permit its upward extraction.

1. Fit the brackets into the relevant bores and fasten

them by means of their screws.

2. Make an opening in the worktop, respecting the

dimensions indicated in the Instruction.

3. Install the cooktop in the worktop.

1 2 3 4

Komentáře k této Příručce

Žádné komentáře

Whirlpool AKM 231/IX Návod k použití Strana 3

Komentáře k této Příručce

Související produkty a manuály pro Sporáky Whirlpool AKM 231/IX